| Section 1 Identification |
| Product Number: | C1732 |
| Health: | 2 |
| Flammability | 0 |
| Reactivity | 0 |
Hazard Rating:
| Least | Slight | Moderate | High | Extreme |
| 0 | 1 | 2 | 3 | 4 |
NA = Not Applicable NE = Not Established
|
|
| Product Name: | Ferric Chloride Laboratory Grade, Lumps |
| Trade/Chemical Synonyms | |
| Formula: | FeCl“½6H’O |
| RTECS: | NO5425000 |
| C.A.S | CAS# 10025-77-1 |
| Section 2 Component Mixture |
| Sara 313 | Component | CAS Number | % | Dim | Exposure Limits: |
|
Ferric Chloride | CAS# 10025-77-1 | 100 % | W/W | OSHA TWA 1 mg(Fe)/mƒ |
|
| Section 3 Hazard Identification (Also
see section 11) |
| May be harmful if swallowed. May cause irritation. Avoid breathing vapors, or dusts. Use with adequate ventilation. Avoid contact with eyes, skin, and clothes. Wash thoroughly after handling. |
| Section 4 First Aid Measures |
May be harmful if swallowed. May cause irritation. Avoid breathing vapors, or dusts. Use with adequate ventilation. Avoid contact with eyes, skin, and clothes. Wash thoroughly after handling.
FIRST AID: SKIN: Remove contaminated clothing. Wash exposed area with soap and water. if irritation persists, seek medical attention.
EYES: Wash eyes with plenty of water for at least 15 minutes, lifting lids occasionally. Seek Medical Aid. INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen
INGESTION: Give several glasses of milk or water. Vomiting may occur spontaneously, but DO NOT INDUCE! Never give anything by mouth to an unconscious person.
|
| Section 5 Fire Fighting Measures |
| Fire Extinguisher Type: | Any suitable for other materials involved. |
| Fire/Explosion Hazards: | Decompses to yield HCL on exposure to light |
| Fire Fighting Procedure: | Wear self-contained breathing apparatus and protective clothing to prevent contact with skin and clothing. |
|
|
| Section 6 Accidental Release
Measures |
Cover with soda ash ; mix and scoop into a large volume of water
|
| Section 7 Handling and
Storage |
| Keep container tightly closed. Store in a cool, dry , well ventilatd area. Avoid exposure to light and moisture; avoid contact with strong mineral acids. Wash thoroughly after handling. |
| Section 8 Exposure Controls
& Personal Protection |
Respiratory Protection:Dust mask or cartridghe respirator
Other Protective Equipment:
Wear appropriate clothing to prevent skin exposure
|
| Section 9 Physical and Chemical Properties |
| Melting Point: | 37 Deg C | Specific Gravity | 1.82
|
| Boiling Point: | 280 to 285 Deg C |
Percent Volatile by Volume: | 0 |
| Vapor Pressure: | Information not available |
Evaporation Rate: | 0 |
| Vapor Density: |
Information not available |
Evaporation Standard: |
|
| Solubility in Water: |
Soluble |
Auto ignition Temperature: |
Not applicable |
| Appearance and Odor: |
Brownish \yellow HCL odor |
Lower Flamm. Limit in Air: |
Not applicable |
| Flash Point: |
Information not available |
Upper Flamm. Limit in Air: |
Not applicable |
|
| Section 10 Stability and Reactivity Information |
| Stability: Stable | Conditions to Avoid: Contact with strong mineral acids. Excessive heat, moisture, and light |
Materials to Avoid:
Acidic conditions, Allyl chloride, Sodium, Potassium |
Hazardous Decomposition Products:
HCL fumes |
| Hazardous Polymerization:Will Not Occur |
| Condition to Avoid:None known |
|
| Section 11
Additional Information |
| If comes in contact with skin, flush with copious amounts of water get medical attention.If comes in contact with eyes flush for 15 minutes get medical attention. If inhaled move to fresh air. Breaathing dust or mist can cause damage to nasal and respiratory passages. Swallowing results in severe damage to mucous membranes and deep tissues. Persons with pre-existig disorders may be more susceptible. |
| DOT Classification: Corrosive solid, acidic, inorganic, n.o.s. (Ferric chloride hexahydrate), 8, UN3260, PG III |
DOT regulations may change from time to time. Please
consult the most recent version of the relevant regulations.
| Revision No:0.1 | Date Entered: 9/1/2006 |
Approved by: WPF |
|
|
|