| Section 1 Identification |
| Product Number: | C2982 |
| Health: | 1 |
| Flammability | 1 |
| Reactivity | 1 |
Hazard Rating:
| Least | Slight | Moderate | High | Extreme |
| 0 | 1 | 2 | 3 | 4 |
NA = Not Applicable NE = Not Established
|
|
| Product Name: | Zinc Metal Pieces, ~ 3/8 x1" Laboratory Grade |
| Trade/Chemical Synonyms | |
| Formula: | Zn |
| RTECS: | ZG8600000 |
| C.A.S | CAS# 7440-66-6 |
| Section 2 Component Mixture |
| Sara 313 | Component | CAS Number | % | Dim | Exposure Limits: |
|
Zinc Metal Pieces, ~ 3/8 x1" | CAS# 7440-66-6 | 100 | W/W | OSHA TWA 5 mg/mƒ |
|
| Section 3 Hazard Identification (Also
see section 11) |
| Generally not hazardous in normal handling, however good laboratory practices should always be used. Avoid long term exposure to skin or by inhalation. |
| Section 4 First Aid Measures |
Generally not hazardous in normal handling, however good laboratory practices should always be used. Avoid long term exposure to skin or by inhalation.
FIRST AID: SKIN: Wash exposed area with soap and water. If irritation persists, seek medical attention.
EYES: Wash eyes with plenty of water for at least 15 minutes, lifting lids occasionally. Seek Medical Aid. INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen
INGESTION: Give several glasses of milk or water. Vomiting may occur spontaneously, but it is not necessary to induce. Never give anything by mouth to an unconscious person.
|
| Section 5 Fire Fighting Measures |
| Fire Extinguisher Type: | Smother with dry powder |
| Fire/Explosion Hazards: | Dust at sufficient concentrations can form explosive mixtures with air. |
| Fire Fighting Procedure: | Wear self-contained breathing apparatus and protective clothing to prevent contact with skin and clothing. |
|
|
| Section 6 Accidental Release
Measures |
Sweep up and place in suitable (fiberboard) containers for reclamation or later disposal.
|
| Section 7 Handling and
Storage |
| Store in a cool, dry, well-ventilated place away from incompatible materials, heat and moisture. Wash thoroughly after handling. |
| Section 8 Exposure Controls
& Personal Protection |
Respiratory Protection:NIOSH approved dust mask
Other Protective Equipment:
Wear appropriate clothing to prevent skin exposure
|
| Section 9 Physical and Chemical Properties |
| Melting Point: | 419° C | Specific Gravity | 7.14
|
| Boiling Point: | 907° C |
Percent Volatile by Volume: | 0 |
| Vapor Pressure: | 1 @ 909° C |
Evaporation Rate: | N/A |
| Vapor Density: |
Information not available |
Evaporation Standard: |
|
| Solubility in Water: |
Insoluble |
Auto ignition Temperature: |
Not applicable |
| Appearance and Odor: |
odorless, grey-blue granules |
Lower Flamm. Limit in Air: |
Not applicable |
| Flash Point: |
N/A |
Upper Flamm. Limit in Air: |
Not applicable |
|
| Section 10 Stability and Reactivity Information |
| Stability: Stable | Conditions to Avoid: None known |
Materials to Avoid:
Acids, alkalies, oxidizers, halogens, chlorine. |
Hazardous Decomposition Products:
Oxides of zinc. |
| Hazardous Polymerization:Will Not Occur |
| Condition to Avoid:None known |
|
| Section 11
Additional Information |
| Effects of overexposure, Acute and Chronic: If fumes are inhaled, may cause fume fever. Ingestion may cause GI disturbances. Contact with skin may cause irritation. Contact with eyes may cause mechanical abrasion or injury to the surface of the eye, noticeable discomfort, redness and tearing. Conditions aggravated/target organs: Persons with pre-existing eye, skin or respiratory conditions may be more susceptible. |
| DOT Classification: Not Regulated |
DOT regulations may change from time to time. Please
consult the most recent version of the relevant regulations.
| Revision No:0 | Date Entered: 9/1/2006 |
Approved by: WPF |
|
|
|